Blog Categories

Using subwoofers to improve sound quality: Part 2 – Room Modes

An introduction to modal resonances

Room modes are caused by perfect constructive interference between a sound wave traveling between two boundaries. In rectangular rooms the first axial mode of a room can be found through an application of the wavelength formula as follows:

1st modal frequency = speed of sound / 2 * distance between boundaries

The axial modes contain the most power and therefore typically cause the largest problems. These modes are caused by interference between two parallel surfaces i.e. those related to the length, width and height dimensions of the room. Let’s look at an example to help illustrate things: The 1st axial mode for a 20ft long room would be: 1140ft per second / (2 x 20ft) = 28.5Hz. If we examined this room using a high resolution acoustic measurement we would expect to see a peak in the frequency response and ringing in the time domain at the resonance frequency (i.e. 28.5Hz). From a sound quality perspective we would expect to hear lack of smoothness, boomy bass and also an impact on clarity, as low level sounds are obscured by the excessive length of time it takes for bass notes to decay.

There are also tangential and oblique modes, which are less powerful and are formed by interference between four and six boundaries respectively. The final consideration is to realize that more than one pattern of constructive interference can fit between two boundaries. In fact modal resonances can be found at multiples of the 1st modal frequency i.e. 28.5*2 (57ft), 28.5*3 (85.5ft), 28.5*4 (114ft), etc. We won’t discuss these added complications further but it is important to be aware of them.

How to use subwoofer placement and numbers to reduce the impact of room modes

To simplify things we will just consider one example – using subwoofers reduce the impact of the 1st axial length mode. The diagram below shows what we would expect to see if we were to measure how sound pressure level varies by distance between the front and back walls of our 20ft long room.

Looking at the diagram you can see that SPL is a maximum near the walls and at a minimum in the center of the room. The minimum point is called a ‘null’. Each side of the null the lobes of the room mode are in opposite polarity.

The effect of a subwoofer on the level of a room mode depends upon where you put the subwoofer. If you put it in the center of the room at the null there would be no energy coupling between the subwoofer and the mode. The mode would not be excited and there would be no measureable peak in the frequency response or ringing in the time domain.

The other way to achieve the same effect is to use two subwoofers, each of which is positioned in a lobe of different acoustic polarity. This means that the positive sound wave created by the subwoofer in the left, positive lobe is met by a sound wave of equal level but negative polarity created by the subwoofer in the other lobe. If you have two sound waves that are identical in frequency and level but the polarities are opposite then there will be perfect cancellation. This means that there will again not be any measurable frequency response peak or time domain ringing.

There is so much that can be achieved by listening to a system to identify a sound quality issue, using measurements to find the cause and then using appropriate solutions. In this case I hope you can see how subwoofers can be used to effectively solve some room mode related problems.


9 thoughts on “Using subwoofers to improve sound quality: Part 2 – Room Modes”

  1. Hi. I have a big dig around 50hz at the center of the room. My room is almost square. H x W x L (3.04m x 3.30m x 3.67m). After reading your article about using subwoofer to cancel room modes. Therefore, can you give me some advice. With the dimension of my room. Can i use one or two subwoofers to cancel that 50hz room mode? Thanks.

    1. I’d recommend using 4 subs, one in each corner. You’ll still have a null vertically at half room height as all the subs will be on the floor, but in your room that should be above ear height.

  2. I have 2 subs in my room pointed toward each other, mid wall on either side of my listening position, about 9.4 feet apart set to 80hz. With one phased out 180 (normal causes cancelation in that location) the bass levels are the same as the fronts when set to full range. With the two active i notice the peaks are canceled and the response is smoothed out.
    if i now set my spl back down to match my system (80db) i notice a drop in bass as compared to the fronts when in full range (my fronts have the same peak as the lone sub did, because they are near a wall).

    My question is, is all that normal?

Leave a Reply to Than Minh Ha Cancel reply

Your email address will not be published. Required fields are marked *